Transcription

User Manual Back-UPSBX Series 750VA, 950VA, 1200VA, 1600VA, 2200VAIMPORTANT SAFETY INSTRUCTIONSRead the instructions carefully and look at the equipment to become familiar with the device beforetrying to install, operate, service or maintain it. The following special messages may appear throughoutthis document or on the equipment to warn of potential hazards or to call attention to information thatclari es or simpli es a procedure.The addition of this symbol to either a “Danger” or “Warning” safety label indicates thatan electrical hazard exists which will result in personal injury if the instructions are notfollowed.This is the safety alert symbol. It is used to alert you to potential personal injury hazards.Obey all safety messages that follow this symbol to avoid possible injury or death.DANGERDANGER indicates a hazardous situation which, if not avoided, will result in death orserious injury.WARNINGWARNING indicates a hazardous situation which, if not avoided, could result in death orserious injury.CAUTIONCAUTION indicates a hazardous situation which, if not avoided, could result in minor ormoderate injury.NOTICENOTICE is used to address practices not related to physical injury.Product Handling Guidelines 18 kg 40 lb18-32 kg40-70 lb32-55 kg70-120 lb 55 kg 120 lb

Safety and General InformationSAVE THESE INSTRUCTIONS –This manual contains important instructions that should be followed during installation andmaintenance of the UPS and batteries.Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damages. This UPS is intended for indoor use only. Mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easilyaccessible. UPS must be connected to an earthed mains socket outlet. Servicing of batteries should be performed or supervised by personnel knowledgeable aboutbatteries and required precautions. In this case, batteries is not user-replaceable. When replacing battery the UPS must be OFF, and its AC inlet unplugged. CAUTION Do not dispose of batteries in a re. The batteries may explode. CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteriesaccording to the instructions. Do not open or mutilate batteries. They contain an electrolyte that is toxic and harmful to the skinand eyes. Failed batteries can reach temperatures that exceed the burn thresholds for touchable surfaces. CAUTION A battery can present a risk of electrical shock and high short circuit current.The following precautions should be observed when working on batteries.a. Remove watches, rings or other metal objects.b. Use tools with insulated handles.c. Wear rubber gloves and boots.d. Do not lay tools or metal parts on top of batteries.e. Disconnect the charging source prior to connecting or disconnecting battery terminals.f. Determine if battery is inadvertently grounded. If inadvertently grounded, remove source fromground. Contact with any part of a grounded battery can result in electrical shock. The likelihoodof such shock can be reduced if such grounds are removed during installation and maintenance. The battery in the Back-UPS Series is not user-replaceable.Radio Frequency WarningThis is a category C2 UPS product. In a residential environment, this product may cause radiointerference, in which case the user may be required to take additional measures.Battery ReplacementCAUTIONRISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKEReplace the battery at least every 5 years.Replace the battery immediately when the UPS indicates battery replacement isnecessary.Replace battery at the end of its service life.Replace batteries with the same number and type of batteries as originally installed inthe equipment.Replace the battery immediately when the UPS indicates a battery over-temperaturecondition, or UPS internal over-temperature, or when there is evidence of electrolyteleakage. Power off the UPS, unplug it from the AC input, and disconnect the batteries.Do not operate the UPS until the batteries have been replaced.Failure to follow these instructions can result in injury.The battery in the Back-UPS is not user-replaceable. Contact SEIT Technical Support for a list ofauthorized service centers near you.For the recycling battery information, please go to apc.com/us.2Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

Product DescriptionThe APC by Schneider Electric Back-UPS offers power and surge protection for wireless networks,computers, gaming consoles and other electronics in your home or business. This UPS supply batterybackup during outages and unstable voltage fluctuations, as well as provide protection from damagingsurges and spikes. It’s equipped with data line surge protection which safeguards your equipment andvaluable files from “back door” surges traveling along data line. They are the choice helps to protectyour sensitive electronics.Place and Power On1. Place the Back-UPS to avoid: Direct sunlight Excessive heat Excessive moisture Excessive dust/dirtFor operation, please place the unit on the floor.2. Connect the battery by pulling the battery handle up,and then pushing it into the unit.3. Connect equipment to the UPS. Avoid using extension cords.4. Plug the Back-UPS power cord directly into a wall outlet, not into a surge protector or power strip.5. Press the ON/OFF button to turn on the unit.The green “Power On” indicator confirms that the Back-UPS is on and ready to provide protection.The Back-UPS should charge for at least 24 hours to ensure sufficient runtime. The unit is beingcharged whenever it is connected to AC power, whether the unit is turned ON or OFF.Operational FeaturesAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels. This allowsthe equipment plugged into the unit to operate during low/high voltage conditions, conserving thebattery power in the event of a power cut. The Back-UPS will switch to battery power if the inputvoltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the ACpower is distorted.PowerChuteTMPersonal Edition SoftwareTo install PowerChute Personal Edition (PCPE) software, connect a USB cable to the data port on theUPS and the other end to a computer with access to the web.On the computer, go to www.apc.com/tools/download. Select “Software Upgrades - PowerChutePersonal Edition” in the “Filter by Software/Firmware” drop down menu. Select the appropriateoperating system. Follow directions to download the software.Quick MuteThe Back-UPS is able to temporarily mute user correctable audible alarms such as On Battery. Duringsuch audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mutethe audible alarm until the condition has been reset. A short double beep will confirm that Quick Mutehas been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other critical events such as Battery replacement and Charger notification can not be temporarilymuted. The unit in these cases must be turned off.Voltage Sensitivity AdjustmentThe Back-UPS detects and reacts to line voltage distortions in PCPE by transferring to battery backuppower to improve protection of connected equipment. In situations where either the Back-UPS or theconnected equipment is too sensitive for the input voltage level, it is necessary to adjust the transfervoltage. Refer to user guide of PowerChute Personal Edition.Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA3

FeaturesA ON/OFF button with indicatorB Input power cordC Battery backup and surge protected outletsD Battery connectorE Circuit breakerF AC power inlet with AC fuse*only for model with IEC outletG USB data portH In/Out Ethernet surge-protected portsBX750MI-GRBX950MI-GR BX750MI-AZModelOutput Typeand QuantityModelOutput Typeand Quantityx4x3BX750MIBX950MIx4x6G HABX950MI-AZ BX750MI-MS BX950MI-MSx4BX750MI-FRG HG HDDDDCCCFEFBBEBX750BX950BX1200MI BX1200MI-GR BX1200MI-FR BX1600MI-MS BX1200MI-AR/AZBX1600MI BX1600MI-GR BX1600MI-FR BX2200MI-MS BX1600MI-AR/AZBX2200MI-ARBX2200MI BX2200MI-GR BX2200MI-FRModelOutput Typeand Quantityx4x6ModelOutput Typeand Quantityx4x4x4BX1200MI-MSx4G Hx1G HDDDDDHHHCECEFFFEBBX1200MIGGGCBX1600MIIEC jumper Cable for PC connection(1.2m)*only for the model with IEC outlet4x2x4x3G Hx2x2x1BX950MI-FRBX2200MIBBX1600MIBX2200MIUSB communication cable (1.2m)Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

SpecificationsModelInputBX750MI BX950MI BX1200MI BX1600MI BX2200MI220-240 VacVoltage50 Hz or 60 Hz (auto-sensing)FrequencyBrownout Transfer140 Vac, typical300 Vac, typicalOver-voltage TransferOutputUPS Capacity (total)Voltage On BatteryFrequency - On Battery230 Vac 10%50 Hz / 60 Hz 0.5HzTransfer Time6ms typical, 10ms max.Protection AC InputCircuit Breaker(only for GR, FR, MSand AR models)Battery750VA/410W 950VA/520W 1200VA/650W 1600VA/900W 2200VA/1200W5A/250Vac7A/250Vac 10A/250Vac 12A/250Vac15A/250VacAC Input FuseT 5A L 250Vac T 8A L 250Vac T 10A L 250Vac T 12A L 250Vac T 15A L 250VacType(maintenance-free)12V, 9AH x 1 12V, 9AH x 1 12V, 9AH x 1 12V, 7AH x 2 12V, 9AH x 2lead acidlead acidlead acidlead acidlead acidAverage LifeThe battery typically lasts for three to ve years.Environmental factors impact battery backup life.Elevated temperatures, high humidity, poor quality mains power,and frequent, short duration discharges will shorten battery life.The battery in the Back-UPS Series is not user-replaceable.Contact SEIT Technical Support for a list of authorized servicecenters near you.Typical Recharge TimePhysical5.4 kgShipping Weight5.9 kgShipping Dimensions(H x Wx D) cmTemperatureIP Rating8 HoursNet WeightDimensions(Hx Wx D) cmOperating6.1 kg7.6 kg10.3 kg16 x12 x 35.56.6 kg12.3 kg19 x14 x 398.6 kg25 x 19.7 x 4311.3 kg13.3 kg29.7 x 23.5 x 49.50 C to 40 CIP20* The length of input power cord is 1.2m. For best operation, do not use output cable longer than 2m.** The length of USB communication cable is 1.2m. For best operation, do not use communication cablelonger than 3m.Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA5

Status IndicatorsLEDAudible AlarmOnOffConstant ToneConstant beeping(every 1/2 second)On4 beeps repeatedConditionOn-line - The Back-UPS is supplying AC power to theconnected equipmentOn Line Overload - The power being used by the connectedequipment has exceeded the capacity of the unit.Disconnect some equipment.Over-temperature Detected - The unit is overheating and willoperate in AVR mode for 1 minute. The Back-UPS will shutdown if the temperature is not lowered. Disconnect some of theconnected equipment.On-Battery - The Back-UPS is supplying battery power.(Off during 4 beeps) every 30 secondsFlashingConstant beeping(every 1/2 second)Constant toneOffShort beep every4 secondsConstant ToneLow Battery - The Back-UPS is supplying battery powerand the battery is near a total discharge state.Replace Battery Detected - The battery needs to be charged,or is at end of life.Note:- If the battery is disconnected, unplug the Back-UPS from ACsource and then turn it off. Refer to the section “Place andPower On” on page 3.- If battery needs replacement, refer to the section “BatteryReplacement” on page 2 for details.Low Battery Shutdown - During On Battery operationthe battery power was almost completely exhausted, and theBack-UPS is waiting for AC power to return to normal.On Line Overload Fault - The connected equipment requiresmore power than provided by the Back-UPS.Unplug devices one at a time to remove overload.If the detected problem is not corrected, contact SEIT TechnicalSupportCharger Detected Fault - Back-UPS has an internalproblem detected, and is no longer powering the load.Contact SEIT Technical SupportLong beep every4 seconds6Over-temperature Detected Fault - The Back-UPS hasoverheated and has shut down. Unplug connected devicesone at a time or wait for a few hours for system to cool down.Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

TroubleshootingDetected Problem and Possible CauseThe Back-UPS will not turn onSolutionThe Back-UPS has not been turned on.The Back-UPS is not connected to ACpower, there is no AC power available at thewall outlet, or the AC power is experiencing abrownout or over voltage condition.Press the ON/OFF button.Make sure the power cord is securely connected to thewall outlet, and that there is AC power available at thewall outlet. Where applicable, check that the walloutlet is switched on.The battery is disconnected.Connected equipment loses powerRefer to the “Place and Power On” on page 3.A Back-UPS overload condition hasoccurred.Remove all nonessential equipment connected to theoutlets. One at a time reconnect equipment to theBack-UPS.Charge the battery for 24 hours to make sure it is fullycharged. If the overload condition still occurs, replacethe battery.The Back-UPS battery is completelydischarged.Connect the Back-UPS to AC power and allowthe battery to recharge for ten hours.Connected equipment does not accept thestep-approximated sine waveform from theBack-UPS.The output waveform is intended for computers andperipheral devices. It is not intended for use with motordriven equipment.The Back-UPS may require service.Contact Schneider Electric Technical Support formore in depth troubleshootingThe ON/OFF button is green and ashing every 30 seconds. 4 beeps repeated every 30 seconds.The Back-UPS is operating on batterypower.The Back-UPS is operating normally on batterypower. At this point the user should save all open les,and shutdown the computer. When AC power isrestored the battery will recharge.The ON/OFF button ashes green and constant beeps every 1/2 second.The Back-UPS battery hasapproximately empty and will shutdownThe Back-UPS battery is near a total dischargestate. At this point the user should save all open les,and shutdown the computer. When AC power isrestored the battery will recharge.The Back-UPS has an inadequate battery runtimeThe battery is not fully charged.The battery is near the end of useful life andshould be replaced.Leave the Back-UPS connected to AC power forten hours while the battery charges to full capacity.As a battery ages, the runtime capability decreases.The UPS and outlets are off but the UPS keeps beeping once every 4 seconds. The audible alarmwill mute after 32 seconds.The UPS have shut down due to low battery,but control power exists.The UPS will return to normal operation once theAC input voltage has returned to a normal range.Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA7

ServiceIf the unit requires service, do not return it to the dealer. Follow these steps:1. Review the Troubleshooting section of the manual to eliminate common problems.2. If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the APC bySchneider Electric website, www.apc.com.a. Note the model number and serial number and the date of purchase. The model and serial numbersare located on the rear panel of the unit.b. Call SEIT Customer Support and a technician will attempt to solve the problem over the phone. Ifthis is not possible, the technician will issue a Returned Material Authorization Number (RMA#).c. If the unit is under warranty, the repairs are free.d. Service procedures and returns may vary internationally. Refer to the APC by Schneider Electricwebsite for country specific instructions.3. Pack the unit in the original packaging whenever possible to avoid damage in transit. Never use foambeads for packaging. Damage sustained in transit is not covered under warranty.4. Always DISCONNECT THE UPS BATTERIES before shipping. The United States Departmentof Transportation (DOT), and the International Air Transport Association (IATA) regulationsrequire that UPS batteries be disconnected before shipping. The internal batteries may remain inthe UPS.5. Write the RMA# provided by Customer Support on the outside of the package.6. Return the unit by insured, pre-paid carrier to the address provided by Customer SupportWarrantyRegister your product on-line. http://warranty.apc.comThe standard warranty is two (2) years from the date of purchase. SEIT standard procedure is to replacethe original unit with a factory reconditioned unit. Customers who must have the original unit back dueto the assignment of asset tags and set depreciation schedules must declare such a need at first contactwith an SEIT Technical Support representative. SEIT will ship the replacement unit once the defectiveunit has been received by the repair department, or cross-ship upon the receipt of a valid credit cardnumber. The customer pays for shipping the unit to SEIT. SEIT pays ground freight transportation coststo ship the replacement unit to the customer.APC by Schneider Electric IT Customer Support WorldwideFor country specific customer support, go to the APC by Schneider Electric website, www.apc.com. 2020 APC by Schneider Electric. APC, the APC logo are owned by SchneiderElectric Industries S.A.S., or their affiliated companies. All other trademarksare property of their respective owners.EN 990-629102/2020